CH.2 -

CH.2 -

CH.2 Electronic Components Eng.Mohammed Alsumady Basics of Electronic Components An electronic component is any device that handles electricity. Electronic components come in many different shapes and sizes, and perform different electrical functions depending upon the purpose for which they are used. Accordingly, electronic equipments make use of a variety of components.

Active Vs Passive Components There are two types of components: passive components and active components. Passive Components : A passive device is one that contributes no power gain (amplification) to a circuit or system. It has no control action and does not require any input other than a signal to perform its function. Since passive components always have a gain less than one, they cannot oscillate or amplify a signal. A combination of passive components can multiply a signal by values less than one; they can shift the phase of a signal, reject a signal because it is

not made up of the correct frequencies, and control complex circuits, but they cannot multiply by more than one because they basically lack gain. Passive devices include resistors, capacitors and inductors. Active Components: Active components are devices that are capable of controlling voltages or currents and can create a switching action in the circuit. They can amplify or interpret a signal. They include diodes, transistors and integrated circuits. They are usually semiconductor devices. Discrete vs Integrated Circuits When a component is packaged with one or two functional elements, it is known as a discrete component. For example, a resistor used to limit the current passing through it functions as a discrete

component. On the other hand, an integrated circuit is a combination of several interconnected discrete components packaged in a single case to perform multiple functions. A typical example of an integrated circuit is that of a microprocessor which can be used for a variety of applications. Component Leads Components can be classified into two types on the basis of the method of their attachment to the circuit board. Through-hole components are those components which have leads that can be inserted through mounting holes in the circuit board. On the other hand, surface mount components

are so designed that they can be attached directly on to the surface of the board. Two types of lead configurations are commonly found in discrete components. The components with axial leads have two leads, each extending from each side of the component like arms. These leads need to be bent for insertion through the holes of a printed circuit board. The other configuration of leads in the components is radial where the leads emanate from the bottom of the components like legs. In the case of integrated circuits, there are a large number of leads which are placed in a row in single line (single in-line package), or in two parallel rows (dual in-line package) These leads can be inserted in

the through-holes in the PCB. High density integrated circuits now come in the form of pin-grid arrays that have several rows of round pins extending from the bottom of the component. Leadless components are also available in the surface mount devices in which no metal leads stick out of the component body. They are attached to a circuit board using some type of metallized termination. Classification of components based on the lead configuration (a) through-hole component (b) surface mount component (c) component with axial leads (d) components with radial leads (e) single-in-line package (f) dual-inline package (g) pin grid arrays (h) leadless components.

Polarized Capacitors Diodes Component Symbols Each discrete component has a specific symbol when represented on a schematic diagram. These symbols have been standardized and specified in the Institute of Electrical and Electronics Engineers (IEEE) standard 315 and 315A . The integrated circuits are generally represented by a block in the schematic diagram and each one does not have a specific symbol.

Resistors The most commonly used component in an electronic assembly is the resistor. It is a passive component which exhibits a controlled value of resistance across its two leads. Resistance, by definition, is the opposition to the flow of current offered by a conductor, device or circuit. Types of Resistors: There are two classes of resistors; fixed resistors and variable resistors. They are also classified according to the material from which they are made. The most commonly used types of resistors are detailed below: Carbon Resistors: They are made either by mixing finely ground carbon with a resin binder and an insulating filler or by depositing carbon film onto a ceramic rod. Most carbon film resistors have low stray capacitance and inductance, so they are usable at higher frequencies. However, their accuracy is limited to 1per cent. In addition, carbon film resistors tend to drift with temperature and

vibration. Metal Resistors: They are made of metal film on ceramic rod or metal glaze (a mixture of metals and glass) or metal oxide (a mixture of a metal and an insulating oxide). Metal film resistors are more stable under temperature and vibration conditions having tolerances approaching 0.5 per cent. Precision metal film resistors with tolerances below 0.1 per cent are also commercially available. Wire-wound Resistors: They are made by winding resistance wire onto an insulting former. They can be made to very close tolerances. Thick Film Resistor Networks: Thick film resistor networks comprise precious metals in a glass binding system which have been screened on to a ceramic substrate and fired at high temperatures. These networks provide miniaturization, have rugged construction, are inherently reliable and are not subject to failures. Networks comprising 1 to 50

resistors, 5 to 20 being typical, are commercially available. Single in-line (SIL) packages, DIP (dual-in-line package) and square packages are commonly available. The resistance network is made with many resistors of the same value. One side of each resistor is connected with one side of all the other resistors inside. A common example of this type of arrangement is to control the current in a circuit powering many light emitting diodes (LEDs). Alternatively, some resistor networks have a 4S printed on the top of the resistor network. The 4S indicates that the package contains four independent resistors that are not wired together inside. The housing has eight leads instead of nine. The reason for using such a large range of materials in the construction of resistors is simply a trade-off between cost and a particular performance characteristic, be it low noise, high stability or small size.

Carbon film resistors From the top of the photograph 1/8W 1/4W 1/2W Metal film resistors From the top of the photograph 1/8W (tolerance 1%) 1/4W (tolerance 1%) 1W (tolerance 5%) 2W (tolerance 5%) Characteristics

The main parameters that define a resistor are detailed below: Resistance: This is the nominal value of resistance between the two leads of the resistor when measured at 25C. Tolerance: This is the maximum deviation of value of resistance from the nominal value, usually given as a percentage of the nominal value. For example: for a 5% tolerance of a resistor of 500 ohms, the value may vary from 475 to 525 ohms. Power Rating: This refers to the maximum power that a resistor can dissipate continuously at a temperature of 70C. This is expressed in watts. Most common resistors are normally 0.25 W and 0.5 W. Modern digital circuits have low current requirements and usually use 0.125 W resistors. Carbon composition and metal resistors are generally available in power ratings of 250 mW, 500 mW, 1 W and 2 W. For dissipating more heat, wire-wound resistors are mostly employed, with the power ratings being up to 25 watts. Temperature Coefficient: It expresses the extent to which the value of resistance will change with temperature. It is usually expressed in parts per million of the nominal value

per degree Celsius (ppm/C). The temperature coefficient of the most commonly used resistors is in the range of 25 to 500 ppmC. Carbon composition resistors have poor stability and relatively poor temperature co-efficient, which is of the order of 1200 ppm/C. Metal film resistors exhibit comparatively low temperature coefficient (250 ppm/C) and good stability, both when stored and under operating conditions. The critical temperature in a resistor is the hot spot temperature, which is the sum of the ambient temperature and the temperature rise caused due to the power being dissipated. Due to uniform construction of the resistor, the maximum temperature is in the middle of the resistor body, this temperature, which is known as the hot spot temperature. Stability or Drift: This is a measure of how much the value of a resistor changes with respect to time because of aging. It is normally measured as a percentage change after 1000 hours of operation at 70C. The

stability of a resistor is defined as the percentage change of resistance value with time. It depends upon the power dissipation and ambient temperature. Maximum Voltage: It represents the maximum dc voltage, which can be safely applied to a resistor on a continuous basis. For most resistors of value around 100 ohms or more, the maximum dc voltage is 1000 volts. Voltage transients above the rated value may induce permanent changes in resistance values. Identification: The value of resistance is either printed in numbers or is put in the form of colourcoded bands around the body. In the colour code, each number from 0 to 9 has been assigned a colour. The colour code comes in the form of four-band. The first band closest to the end of the resistor represents the first

digit of the resistance value. The second band gives the second digit and the third band gives the number of zeros to be added to the first two digits to get the total value of theresistor. The fourth band indicates the tolerance. If the fourth band is absent, the tolerance is 20%. In the five-band colour code, the first three bands indicate the value, the fourth band indicates the multiplier factor, and the fifth band, the tolerance of the resistor. In the six-band colour code, the sixth band indicates the temperature coefficient of variation of resistance in terms of parts per million per degree centigrade (ppm/C). When the value and tolerance of the resistor are printed on the resistor body, the values of the tolerances are coded as follows:

F = 1%, G = 2%., j = 5%, K = 10%, M = 20% Variable Resistors or Potentiometers Variable resistors basically consist of a track of some type of resistance material with which a movable wiper makes contact. Variable resistors or potentiometers (pots as they are popularly called) can be divided into three categories depending upon the resistive material used. (a) carbon composition (b) multi-turn cermet (c) wire wound. Carbon: Carbon potentiometers are made of either moulded carbon composition giving a solid track or a coating of carbon plus insulating filler onto a substrate. Cermet: Cermet potentiometers employ a thick film resistance coating on a ceramic substrate.

Wire-wound: Nichrome or other resistance wire is wound on to a suitable insulating former for the construction of wire-wound potentiometers. Potentiometers can be categorized into the following types depending upon the number of resistors and the control arrangement used: Single Potentiometers: Potentiometer control with one resistor. Tandem Potentiometers: Two identical resistor units controlled by one spindle. Twin Potentiometers: Two resistor units controlled by two independent concentric spindles. Multi-turn Potentiometers: Potentiometer with knob or gear wheel for resistance adjustment; they may have up to 40

rotations of spindle. Potentiometers are typically used for setting bias values of transistors, setting time constants of RC timers, making gain adjustments of amplifiers, and carrying current or voltage in control circuits. Therefore, they are packaged in such a way that they are compatible with PCB mounting applications. Variable resistors can be constructed to follow one of the following laws: Linear: The resistance of the pot is distributed evenly over its entire length. Log: The resistance of the pot varies so as to follow the logarithmic law. In these pots, when the wiper is turned, the resistance increases (from zero) very slowly and gradually until

about the half way mark. From then onwards, as the wiper shaft is turned further, the resistance will increase much more rapidly in comparison with the first half of the pot-rotor rotation. Sine-Cosine Potentiometers: As the name implies, the variation of resistance over the track, when the wiper moves, follows the sine-cosine law. The total operative track length over 360 degrees of rotation is divided into four quadrants of 90 degrees each. Light-dependent Resistors (LDRs) Light-dependent Resistors are made of cadmium sulphide. They contain very few free electrons when kept in complete darkness and therefore, exhibit very high resistance. When subjected to light, the electrons are liberated and the

material becomes more conducting. When the light is switched off, the electrons are again recaptured and the material becomes less conducting or an insulator. The typical dark resistance of LDRs is 1 MOhms to 10 MOhms. Its light resistance is 75 to 300 ohms. The LDRs take some finite time to change its state and this time is called the recovery time. The typical recovery rate is 200kOhms/sec. Thermistors Thermistors are resistors with a high temperature co-efficient of resistance. Thermistors with negative temperature co-efficient (fall in resistance value with an increase in temperature) are the most popular. They are oxides of certain metals like manganese, cobalt and nickel. Thermistors are available in a wide variety of shapes and forms suitable for use in different applications. They are available in the form of disks, beads or

cylindrical rods. Thermistors have inherently non-linear resistancetemperature characteristics. However, with a proper selection of series and parallel resistors, it is possible to get a nearly linear response of resistance change with temperature over a limited range. Thermistors with a positive thermo-resistive co-efficient are called posistors. They are made from barium titanate ceramic and are characterized by an extremely large resistance change in a small temperature span. Thermistors have various applications such as excess current limiters, temperature sensors, protection devices against over-heating in all kinds of appliances such as electric motors, washing Machines. Capacitors A capacitor, like a resistor, is also a passive component, which can be used to store electrical charge. Capacitors find widespread applications in the electrical and electronics fields in the form of:

Ripple filters in power supplies; Tuning resonant circuits, oscillator circuits; Timing elements in multi-vibrators, delay circuits; Coupling in amplifiers; De-coupling in power supplies and amplifiers; and Spark suppression on contacts on thermostats and relays. A capacitor (also called a condenser) consists of two facing conductive plates called electrodes, which are separated by a dielectric or insulator. The dielectric can be made of paper, mica, ceramic, plastic film or foil. To make a practical capacitor, a lead is connected to each plate or electrode. The charge Q which can be stored in a capacitor, when connected to a voltage V across it, is given by: Q = CV

Capacitance is measured in farads. A capacitor has a capacitance of one farad when one coulomb charges it to one volt. The farad is too large a unit. The usual sub-units used are microfarad and the picofarad. The value of a capacitor is indicated on the body of the capacitor, either in words or in a colour code. The value of a capacitor is also sometimes written on the body in the form of numbers. Values beginning with decimals are usually measured in microfarads (F), while all other values are assigned to be in picofarads (pF). Four-digit values are also indicated in picofarads but without a multiplier. Some capacitors are coded with a three-digit number which is similar to the colour band system, with a value and multiplier numbers. For example, 203 means that 2 and 0 are attached to 3 zeros and the value of the capacitor would be 20,000 pF or .02

F. The tolerance letter codes indicate: F= 1%, G = 2%, J = 5%, K = 10%, M = 20% Types of Capacitors Capacitors are categorized into various types depending upon the dielectric medium used in their construction. The size of the capacitor, its tolerance and the working voltage also depend upon the dielectric used. Paper Capacitors: Paper capacitors make use of thin sheets of paper wound with thin aluminium foils. In order to increase the dielectric strength and to prevent moisture absorption, the paper is impregnated with oils or waxes. The capacitor is normally encapsulated in resin. Paper capacitors tend to be large in size due to the thickness of paper and foil.

The thickness is reduced in metallized capacitors by directly depositing the aluminium on the dielectric. Typical range : 10 nF to 10 F Typical dc voltage : 500 V(max.) Tolerance : 10% Mica Capacitors: A mica capacitor is made by directly metallizing the thin sheets of mica with silver and stacking together several such sheets to make the complete capacitor. The assembly is encapsulated in resin or moulded in plastic. Typical range : 5 pF to 10 nF Typical dc voltage : 50 to 500 V Tolerance : 0.5% Ceramic Capacitors: Ceramic capacitors generally employ barium titanate

as the dielectric medium. However, low-loss ceramic capacitors use steatite, which is a natural mineral. A thin plate of ceramic is metallized on both sides and the connecting leads are soldered to it. The body is coated with several layers of lacquer. Modern ceramic capacitors of the monolithic type are made of alternate layers of thin ceramic dielectric and electrodes, which are fired and compressed to form a monolithic block. These capacitors have a comparatively small size. Typical range : (a) Low loss (steatite) 5 pF to 10 nF (b) Barium titanate 5 pF to 1 mF Typical voltage range for both: 60 V to 10 kV Tolerance : 10% to 20% Plastic Capacitors: The construction of plastic capacitors is very similar to that of paper capacitors. They are of both foil and metallized types. Polystyrene film or

foil capacitors are very popular in applications requiring high stability, low tolerances and low temperature co-efficient. However, they are bulky in size. For less critical applications, metallized polyethylene film capacitors are used. They are commonly referred to as polyester capacitors. Electrolytic Capacitors: High value capacitors are usually of electrolytic type. They are made of a metal foil with a surface that has an anodic formation of metal oxide film. The anodized foil is in an electrolytic solution. The oxide film is the dielectric between the metal and the solution. The high value of capacity of electrolytic capacitors in a small space is due to the presence of a very thin dielectric layer. Electrolytic capacitors are of the following types: Aluminum Tantalum Electrolytic capacitors exhibit a very wide range of tolerances, typically ranging from 20 to +50%. They are usually polarized. Care must be taken not to reverse

the voltage applied across it. If a reverse voltage is applied, the dielectric will be removed from the anode and a large current will flow as oxide is formed on the cathode. Sometimes the gases released from the capacitor may build up and cause the capacitor to explode and damage other parts of the circuit. Packages Capacitors are available in a large variety of packages, shapes and dimensions. The most common packages are axial, disc, rectangular, tubular, etc. Performance of Capacitors

The important parameters which characterize a capacitor are: Capacitance: This is the nominal value of a capacitor, measured in Farads (or its submultiples) at 25 C. Tolerance: This refers to the deviation of the actual value of a capacitor from its nominal value. Different types of capacitors have different values of tolerance. Working Voltage: This is the maximum voltage which can be applied continuously across the capacitor. This is indicated as ac or dc. The maximum voltage that causes permanent damage in the dielectric is referred to as breakdown voltage. This is generally twice the working voltage.

Temperature Coefficient: It indicates the change in the value of capacitance with temperature and is expressed as parts per million per degree Celsius (ppm/C). DC Leakage: The amount of current which flows through a charged capacitor because of losses due to the conductivity of the dielectric. Parasitic Effects: The capacitor impedance is a function of frequency: at low frequencies, the capacitor blocks signals and at high frequencies, the capacitor passes signals. Depending on the circuit configuration, the capacitor can pass the signal to the next stage or it can shunt it to ground. All capacitors have a self-resonant frequency. Aluminium electrolytic capacitors have a very low self-resonant frequency, so they are not effective in high frequency applications above a few hundred kHz. Tantalum capacitors have a mid-range self-resonant frequency. Thus, they are found in applications up to several MHz and beyond that, ceramic and mica capacitors are preferred because they have self-resonant frequencies ranging into hundreds of MHz. Very low frequency and timing applications require highly stable capacitors. The dielectric of these types are made from paper, polypropylene, polystyrene

and polyester. They exhibit low leakage current and low dielectric absorption. The dissipation factor (DF) is mathematically defined as R/X where R is the resistance in the capacitor and X is the reactance of the capacitor. The higher the R, the higher would be the DF and poorer the capacitor. From the formula, DF = R/X, it is clear that DF is an inverse function of X. As X goes down, DF goes up and vice versa. DF varies proportionately with frequency, which shows that DF is a function of the test frequency. The quality factor Q serves as a measure of the purity of a reactance, i.e. how close it is to being a pure reactance i.e. having no resistance. This represents as the ratio of the energy stored in a component to the energy dissipated by the component. Q is a dimensionless unit and is expressed as Q = X/

R. However, Q is commonly applied to inductors; for capacitors the term more often used to express purity is dissipation factor (DF). This quantity is simply the reciprocal of Q. Variable Capacitors Variable capacitors are constructed by using any one of the dielectrics like ceramic, mica, polystyrene or teflon. Basically, a variable capacitor has a stator and a rotor. The area of the stator is fixed and turning the rotor from 0 to 180 varies the amount of plate surface exposed, thereby varying the value of the capacitor. In most variable capacitors, the change in capacitance is linear throughout the rotation of the rotor. Variable capacitors are available in the following two configurations:

Button type: This has a variable rotor. Tubular type: This has an adjustable core. It may be noted that adjustments made with a variable capacitor by using a metal screwdriver will alter when the screwdriver is lifted from the turning screw. This is because placing the metal screwdriver on this screw changes the effective area of the metal plated surface of either the stator or, more often, the rotor. In such a case, the use of a non-metallic screwdriver is recommended. Inductors Inductance is the characteristic of a device which resists change in the current through the device. Inductors work on the principle that when a current flows in a coil of wire, a magnetic field is produced, which collapses when the current is stopped.

The collapsing magnetic field produces an electromotive force which tries to maintain the current. When the coil current is switched, the induced EMF would be produced in such a direction, so as to oppose the build-up of the current. The unit of inductance is Henry. An inductance of one Henry will induce a counter emf (electromotive force) of one volt when the current through it is changing at the rate of one ampere per second. Inductances of several Henries are used in power supplies as smoothing chokes, whereas smaller values (in the milli-or micro-Henry ranges) are used in audio and radio frequency circuits.

The inductors are also sometimes called coils. The Inductors are available in many sizes and shapes. The value of an inductor may be printed on the component body or it may be printed with color bands , much in the same way as a resistor. For example, if the first and second bands of an inductor are red (value 2) and the third band is orange (value 3), the value of the inductor is 22,000 H. A fourth silver band will indicate its tolerance as 10%. The primary use of an inductor is filtering. There are two very different types of filter inductors: the high current inductors wound around a large core are used in power supply filters, and the low current air core inductors are used in signal filters. The basic components of an inductor are the former (or bobbin), winding wire and the core material. Bobbins are normally made

of moulded plastic and carry the wire and the core. Winding is usually copper wire whose diameter is calculated to keep the temperature rise under full load to an acceptable level. The core material can be laminated steel, powdered iron or ferrite. The shape of the core is also variable. The toroidal coil consists of copper wire wrapped around a cylindrical core. It is possible to make it so that the magnetic flux which occurs within the coil doesnt leak out, the coil efficiency is good, and that the magnetic flux has little influence on other components. Toroids are the most efficient cores in ferrites, but they are difficult to wind. Air core coils are frequently used at very high frequencies. High current inductors require cores to keep the losses within acceptable

limits and to achieve high performance. The cores are big and heavy, so they have large weight and size. Switching power supplies require extensive inductors or transformers to control the switching noise and filter the output voltage waveform. Low current inductors are used for filters in signal processing circuits. An inductive/capacitive filter has sharper slopes than a resistive/capacitive filter, and is thus a more effective filter in some applications. In general, inductors are rarely seen outside power circuits. The range of inductor style and shape is considerably larger than for either capacitors or resistors. This is because many organizations need to wind their own inductors to meet their specific demands, which could be for RF coils, audio filters, power supply chokes, etc. Variable inductors in which the inductance value can be adjusted are also available. The ferrite core of the inductor is made like a screw. The core can

be made to move in and out of the inductor by turning it with a screwdriver. A special plastic screwdriver is better to use for adjustment of the coils. Diodes A diode is an active component through which the current flows more easily in one direction than in the other. It is made from semiconductor material. The main functions of the diode in a circuit are to act as a switching device, a detector or a rectifier. Since the diode is a two-element device, its symbol shows the two electrodes. The cathode and anode ends of metal encased diodes can be identified on the body. The arrow head of the symbol points in the direction of conventional current flow. In case of glass encased diodes, the cathode end is indicated by a stripe, a series of stripes or a dot. For most silicon or germanium diodes

with a series of stripes. Conventional diodes normally show a low value of forward resistance and a very high value of reverse resistance. The variation in resistance is due to the non-linear voltage/current characteristics of the diode. Signal diodes are general purpose diodes, which find applications involving low currents and a wide range of voltages, sometimes extending upto 50 kV. Switching diodes change their state from conducting to non-conducting state and vice versa in a very short time when the voltage is reversed. Rectifiers are similar to signal diodes, but are more suitable for high currents. Low and medium power diodes are usually available in axial packages whereas high power diodes are available in a large

variety of packages of a vast range of shapes and sizes. Very high power diodes have a thread for mounting on to a PCB or a heat sink. Diode arrays or networks, containing up to 48 devices are also available in packages similar to integrated circuits. Devices containing four diodes in one package are called diode bridges. Diode bridges with large current capacities require a heat sink. Typically, they are screwed to a piece of metal or the chassis of the equipment in which they are used. The heat sink allows the device to radiate excessive heat. Special Types of Diodes there are many other types of diodes which have special characteristics. Following is a description and characteristics of some of the special types of diodes.

Zener Diode: at some specific value of reverse voltage, a very rapid increase occurs in reverse current. This potential is called breakdown avalanche or the zener voltage and may be as low as 1 volt or as high as several hundred volts, depending upon the construction of the diode. A zener diode has very high resistance at bias potentials below the zener voltage. This resistance could be several Megohms. At zener voltage, the zener diode suddenly shows a very low resistance, say between 5 and 100. A zener diode behaves as a constant voltage source in the zener region of operation, as its internal resistance is very low. The current through the zener diode is then limited only by a series resistance . The value of series resistance is such that the maximum rated power rating of the zener diode is not exceeded. In order to help in distinguishing the zener diode from a general purpose diode, the former is usually labeled with its specified breakdown voltage. Since this voltage is required in the circuit design, the value is generally indicated on the diode. For example,

some common values are 6.8 V, 7.2 V, 9.6 V etc. Varactor Diode A varactor diode is a silicon diode that works as a variable capacitor in response to a range of reverse voltage values. Varactors are available with nominal capacitance values ranging from 1 to 500 pF, and with maximum rated operating voltages extending from 10 to 100 volts. They mostly find applications in automatic frequency control circuits. In a typical case, a varactor shows 10 pF capacitance at reverse voltage of 5 volts and 5 pF at 30 volts. Varistor A varistor is a semiconductor device that has a voltagedependent non-linear resistance which drops as the applied voltage is increased. A forward biased germanium diode shows such types of characteristics

and is often used in varistor applications. Symmetrical varistor arrangements are used in meter protection circuits wherein the diodes bypass the current around the meter regardless of the direction of current flow. If the meter is accidentally overloaded, varistors do not permit destructive voltages to develop across the meter. Light Emitting Diodes (LED) A light emitting diode is basically a pn junction that emits light when forward biased. LEDs are available in various types and mounted with various colored lenses like red, yellow and green. They are used mostly in displays employing seven segments that are individually energized to form alphanumeric characters.

LED displays are encountered in test equipment, calculators and digital thermometers whereas LED arrays are used for specific applications such as light sources, punched tape readers, position readers, etc. Electrically, LEDs behave like ordinary diodes except that their forward voltage drop is higher. For example, the typical values are; IR (infra-red): 1.2 V, Red: 1.85 V, Yellow: 2 V, Green: 2.15 V. Further, the actual voltages may vary depending upon the actual technology used in the LED. Photodiode A photodiode is a solid state device, similar to a conventional diode, except that when light falls on it ( pn junction), it causes the device to

conduct. It is practically an open circuit in darkness, but conducts a substantial amount of current when exposed to light Tunnel Diode (TD) A tunnel diode is a pn junction which exhibits a negative resistance interval. Negative resistance values range from 1 to 200 ohms for various types of tunnel diodes. Transistors Bipolar Transistors: The most commonly used semiconductor device is the

transistor having the characteristic to control voltage and current gain in an electronic circuit. These properties enable the transistor to provide amplification, rectification, switching, detection and almost any desired function in the circuit. It is the basic device of all solid state electronics, both as a single component or as an element of integrated circuit. All transistors have leakage current across their reverse-biased base-collector diodes. For silicon transistors, this current is more than several nanoamperes. In germanium transistors, the leakage current may even be several microamperes. Leakage current increases with temperature and doubles about every 10 C. More than 500 packages of transistors are listed in

the component manufacturers catalogues. However, only about 100 types are in common use. Metallic packages (TO-3, TO-5 and TO-18) have been in use for a long time. However, they have been mostly replaced in low and medium power applications by cheap plastic packages due to the low cost of the latter. For high power applications, however, metallic packages, both stud or bolt type, are still common, though flat type packages are being replaced by plastic versions, with metallic tabs to improve heat dissipation. Power Transistors

The junctions of the power transistors have comparatively larger areas than small signal transistors and have the following characteristics: Forward resistance values are generally lower than those for small signal silicon transistors. Similarly, they have lower reverse resistance values. Power transistors are usually mounted on the heat sinks or heat radiators. They are sometimes mounted on the chassis using silicone grease to increase heat transfer. The Test of Silicon Power Transistor Darlington Transistors

A Darlington is a special type of configuration usually consisting of two transistors fabricated on the same chip or at least mounted in the same package. Darlington pairs are often used as amplifiers in input circuits to provide a high input impedance. Darlingtons are used where drive is limited and a high gain, typically over 1000, is needed. In this configuration the emitter base junctions are connected in series and the collector terminals are connected in parallel. A Darlington configuration behaves like a single transistor where-in the current gains (hfe) of the individual transistors it is composed of are multiplied together and the base-emitter voltage drops of the individual transistors are added together. Field-effect Transistors

Field-effect transistors, like bipolar transistors, have three terminals. They are designated as: source, drain and gate, which correspond in function to the emitter, collector and base of junction transistors. Source and drain leads are attached to the same block (channel of n or p semiconductor material). A band of oppositely doped material around the channel (between the source and drain leads) is connected to the gate lead. In normal junction FET operation, the gate source voltage reverse-biases the pn junction, causing an electric field that creates a depletion region in the source-drain channel. In the depletion region the number of available current carriers is reduced as the reverse-biasing voltage increases, making source drain current a function of gate-source voltage. With the input (gate-source) circuit reverse biased, the FET presents a high impedance to its signal source. This is in contrast to the low impedance of the forward-biased junction bipolar transistor base-emitter circuit. Since there is no input current FETs emit less noise than junction transistors.

MOSFET transistors, including those in the CMOS integrated circuits, are Enhancement Mode type devices. With zero gate-to-source bias, these devices are off, and are increasingly turned on by the application of increasing gate-tosource bias (positive for n-channel, negative for p-channel). There are three different types of field-effect transistors including; (a) Junction gate; (b) Insulated gate (non-enhanced type or Depletion Type); and (c) Insulated gate (enhanced type). Each type comes with either n-channel or p-channel. The junction gate and non-enhanced type insulated gate FETs are basically ON devices like vacuum tubes. These two devices must be biased off. On the contrary, the enhanced type insulated gate FET is basically an OFF device and must be biased on.

Insulated Gate Bipolar Transistor (IGBT) Prior to the development of IGBTs, power MOSFETs were used in medium or low voltage applications which require fast switching, whereas bipolar power transistors and thyristors were used in medium to high voltage applications which require high current conduction. A power MOSFET allows for simple gate control circuit design and has excellent fast switching capability. On the other hand, at 200 V or higher, it has the disadvantage of rapidly increasing on-resistance as the break-down voltage increases. The bipolar power transistor has excellent on-state characteristics due to the low forward voltage drop, but its base control circuit is complex and fast switching operation is difficult as compared with the MOSFET. The IGBT has the combined advantages of the above two devices. The IGBT structure is a combination of the

power MOSFET and a bipolar power transistor. Transistor Type Numbers Over the years, manufacturers have issued about 50,000 to 100,000 separate transistor type numbers. A vast majority of these, are, however, no longer in use. Some of the commonly used type numbers are detailed below: Joint Electron Device Engineering Council (JEDEC) The transistor markings in this case take the following form: Digit, letter, serial number, (suffix), where the letter is always N, the serial number runs from 100 to 9999 and tells nothing about the transistor except its approximate time of introduction. The (optional) suffix indicates the gain (hfe, or B). For example: A = low gain

B = medium gain C = high gain No suffix = ungrouped (any gain) Examples: 2N904, 2N3819, 2N2221A. The data sheets give information on the actual gain spread and groupings. The reason for gain grouping is that the low gain devices are usually cheaper than the high gain devices. Japanese Industrial Standard (JIS): These take the following form: Digit, two letters, serial number, (suffix). The letters indicate the application area according to the following code: SA = PNP HF transistor SB = PNP AF transistor

SC = NPN HF transistor SD = NPN AF transistor SJ = P-channel FET/MOSFET SK = Nchannel FET/MOSFET The serial number runs from 10 to 9999. The (optional) suffix indicates that the type is approved for use by various Japanese organizations. Since the code for a transistor always begins with 2S, it is sometimes omitted. For example, a 2SC733 would be marked C733. The typical examples of JIS based transistor markings are: 2SA1187, 2SB646, 2SC733. Pro-electron System: This European system adopts the following form:

Two letters, (letter), serial number, (suffix). The first letter indicates the material as follows: A = Germanium (Ge) B = Silicon (Si) C = Gallium Arsenide (GaAs) R = Compound materials The majority of transistors are of silicon, and therefore, begin with a B. The second letter indicates the device application: C = Transistor, AF, small signal D = Transistor, AF, power F = Transistor, HF, small signal L = Transistor, HF, power U = Transistor, power, switching The third letter indicates that the device is intended for industrial or professional rather than commercial applications. It is usually a W, X, Y or Z. The serial number runs from 100 to 9999. The suffix indicates the gain grouping. Examples: BC108A, BAW68, BF239, BFY51.

Manufacturers Codes Manufacturers often introduce their own types, for commercial reasons, or to emphasize that the range belongs to a special application. Some common brand specific prefixes are: TIS = Texas Instruments, small signal transistor (plastic case) TIP = Texas Instruments, power transistor (plastic case) MPS = Motorola, low power transistor (plastic case) MRF = Motorola, HF, VHF and microwave transistor RCA = RCA.

Thyristors Thyristors is family of components which is mostly used in all solid state power control and switching circuits, thereby replacing the old relay circuits. The following types of thyristors are widely used: Silicon-controlled rectifier (SCR). Triac (bidirectional thyristor). Thyristors are used extensively in power control circuits. They are particularly suited for ac power control applications such as lamp dimmers, motor speed control, temperature control and invertors. They are also employed for overvoltage protection in dc power supplies. The thyristor is basically a four-layer pnpn device The device is normally off, but a trigger pulse at the gate switches the thyristor from a nonconducting state into a low resistance forward

conducting state. Once triggered in conduction, the thyristor remains on unless the current flowing through it is reduced below the holding current value or it is reverse-biased. This means that the thyristor has extremely non-linear voltage-current characteristics . In case of a motor speed control or light dimmer, the exact time when the thyristor is triggered relative to the zero crossings of the ac power is used to determine the power level. Triggering the thyristor early in the cycle results in the delivery of high power to the load. Similarly, if the thyristor is triggered late in the cycle, only a small amount of power is delivered to the load. The advantage of thyristors over simple variable resistors is that they dissipate very little power as they are either fully on or fully off.

The triac is similar in operation to two thyristors connected in reverse-parallel, but with a common gate connection. This means that the device can pass or block current in both directions. Obviously, it can be triggered into conduction in either direction by applying either positive or negative gate signals. Many transistor packages are used for packaging SCRs and TRIACs. Special packages have however, been also developed. The most common packages are TO-49, TO-118, TO-65 and TO-200. TO-49 Integrated Circuits An integrated circuit contains transistors, capacitors, resistors and other parts packed on a single chip. Its function is similar to that of a circuit made with separate components. However,

the components are formed in a miniature form, so that they can be packed in high density on a base of silicon. There are many kinds of integrated circuits and they come in several forms of packages. The number of pins on the integrated circuits differ from package to package depending upon the function of the IC. The IC can be attached directly to a printed circuit board with a solder. However, some designers prefer to use an IC socket as it is easy to exchange it. Broadly, there are two types of integrated circuits: linear integrated circuits and digital integrated circuits. Linear Integrated Circuits Linear integrated circuits are characterized by an output that is proportional to its input. There are many families of linear integrated

circuits such as: (I) operational amplifiers; (II) differential amplifiers; (III) instrumentation amplifiers; (IV) audio and video amplifiers; (V) wide band amplifiers; (VI) radio frequency amplifiers; (VII) voltage/current regulators; and (VIII) analog-to-digital (A/D) and digital-to-analog (D/A) converters. Most of these provide, in a single package, a circuit equivalent to many discrete components. However, an important class of linear integrated circuits is operational amplifiers (op-amps). These amplifiers were originally utilized in analog computers to perform various mathematical operations such as addition, subtraction, integration and differentiation. Op-amps are now used to perform a variety of precise circuit functions. There are over 2500 types of commercially available op-amps. Most are low power devices with a power dissipation of up to 1W. However, they differ according to their voltage gain, temperature range, noise level and other characteristics.

Operational Amplifiers (Op-amp) An operational amplifier is a complete amplifier circuit constructed as an integrated circuit on a single silicon chip. Inside, it contains a number of transistors and other components packaged into a single functional unit. It has a balanced arrangement in the input and is characterized by extremely high dc (static) and low frequency gain, a very high input impedance, a low closed loop output impedance and a fairly uniform roll-off in gain with frequency over many decades. The linear roll-off characteristic of an operational amplifier gives it the universality, and ability to accept feedback from a wide variety of feedback networks with excellent dynamic stability. The particular application of an op-amp is obviously determined by the device and its external circuit connections. The signal input terminals are described by minus () and plus (+) signs

inside the triangle. The () input is called the inverting input, because the output voltage is 180 degrees out of phase with the voltage to this input. On the other hand, the (+) input is called the non-inverting input because the output voltage is in phase with this voltage applied to this terminal. The names inverting and non-inverting terminals have been given to indicate the phase of output signal in relation to the voltage applied at the inputs. Operational amplifiers are available both in metal as well as dual-in-line epoxy packages. Sockets for both types of packages are available and are mostly used in the printed circuit boards, though the IC can be directly soldered on the board.

Op-amp Identification In general, the op-amps carry the following three types of information on the pack: uA 741 Device type T Package type C Temperature Device Type: This group of alphanumeric characters defines the data sheet which specifies the functional and electrical characteristics of the device. Package Type: One letter represents the basic package style. The various letters are: D = Dual in-line package (hermetic, ceramic). F = Flat pack. H = Metal can package. J = Metal power package (TO-66 outline).

K = Metal power package (TO-3 outline). P = Dual-in line package. R = Mini DIP (hermetic, ceramic); T = Mini DIP . U = Power package (TO-220 outline). Temperature Range: The three basic temperature grades in common use are: C = Commercial 0 C to + 70 C M = Military 55 C to + 125 C V = Industrial 40 C to + 85 C Examples:

uA 710 FM: This code indicates a A 710 A 710 voltage comparator in a flat pack with military temperature rating. uA 725 HC: This number code indicates a A 710 A 725 instrumentation operational amplifier, in a metal can with a commercial temperature rating capability. In addition, the year of manufacture, and manufacturers identification are also given on the device. Three-terminal Voltage Regulator These are integrated circuits with three pins in which the input is applied

to pin 1, the output is taken from pin 3, and the centre leg is the ground. They are available for fixed voltages like 5 V, 9 V, 12 V, etc. Most of the modern equipment makes use of these regulators. A typical three-pin regulator for +5 volts is 78L05. The size and form of this regulator are similar to that of a 2SC1815 transistor. 7805 is again a +5 volt three-pin regulator but with the current capacity of 500 mA to 1 A depending upon the heat sink used. The input voltage in both types of 7805 is 7V . There are many types of three-pin regulators with different output voltages such as: 5 V, 6 V, 8 V, 9 V, 10 V, 12 V, 15 V, and 18 V. Digital Integrated Circuits Digital integrated circuits are used extensively in all branches of electronics from computing to industrial control, electronic instruments, communication systems and medical equipment. In

fact, there does not seem to be any area in electronics where-in digital circuits are not or will not be used in some form or the other. The basic reason for this is that digital circuits operate from defined voltage levels, which reduces any uncertainty about the resulting output and the behavior of a circuit. Many circuits operate with voltages that can only be on or off, e.g. a light can be on or off, a motor can be running or stopped, or a valve can be open or shut. All these are digital operations and would need digital circuit elements for their operation and control. Digital circuits cover a wide range of applications, from high current industrial motors to microprocessors. However, the basic elements of all digital circuits are logic gates that perform logical operations on their inputs.

The Logic Families The logic function of any IC gate is the same irrespective of the technology employed in fabricating the gate. Transistor-Transistor Logic (TTL): The most popular and most widely employed logic family is the transistor-transistor family. The various logic gates are manufactured in the integrated circuit form by most manufacturers of semiconductors. The basic element in TTL circuits is the bipolar transistor. The popularity of the TTL family rests on its good fan-in and fan-out capabilities, high speed (particularly Schottky TTL version), easy interconnection to other digital circuits and relatively low cost. The main characteristics of TTL logic are: propagation delay 10ns, flip-flop rate 20 MHz, fanout 10, noise margin 0.4 V, dissipation per gate 10 mW. The standard TTL gates are marketed as 74 series which can operate up to 70

C. However, 54 series are operatable up to a temperature of 125 C. Most IC packages contain more than one gate. For example, IC 7400 is a quad two-input NAND gates whereas 7420 is a dual four-input NAND gates. There are various types of TTL families, which mostly differ only in speed and power dissipation. Schottky TTL: The gates in the family are faster than those in standard TTL and consume much less power. Schottky TTL logic gates are available in the integrated form as 74S/54S series. A low power Schottky TTL series is also available as 54LS/74LS. Emitter-coupled Logic (ECL Family): The ECL family provides another means of achieving higher speed of the gate. This differs completely from the other types of logic families in that the transistors, when conducting, are not saturated with the result that logic swings are reduced. For example, if the ECL gate is operated

from 5 volts, the logic 0 is represented by 0.9 V and logic 1 by 1.75 V. CMOS Logic Families: The complementary metal-oxide semiconductor (CMOS) logic families offer significant advantages over bipolar transistor-based logic circuits, particularly as they feature very low power dissipation and good noise immunity. The great advantage of CMOS technology is the possibility of high density packing of a large number of devices. The technique is most suitable for the construction of large scale integrated circuits rather than simple gates and flip-flops. Commercially available CMOS gates are available as 4000 series. For example, quad two-input AND gate in CMOS comes as 4081 (7408 TTL) while quad two-input NOR gate as 4001 (7402 TTL). Placing +12 V (logic 1) on the input turns the n-channel ON and p-channel MOSFET OFF. The output is then essentially at ground or a logic 0 level, which completes the inversion.

Categories of Integrated Circuits Based on Packing Density SSI (Small scale integration): refers to integration levels typically having about 12 equivalent gates on chip. They are available in 14 or 16 pin DIP or Flat packs. MSI (Medium scale integration): means integration typically between 12 and 100 equivalent gates per IC package. It is available in 24-pin DIP or Flat pack or 28-pin ceramic chip carrier package. LSI (Large scale integration): implies integration typically up to 1000 equivalent gates per IC package. It is includes memories and some microprocessor circuits. VLSI (Very large scale integration): means integration levels with extra high number of gates, say up to 1,00,000 gates per chip.

For example, a RAM may have more than 4000 gates in a single chip, which is why it comes under the category of VLSI device. Logic IC Series The commonly used logic IC families are:

(a) Standard TTL (Type 74/54) (b) CMOS (Type 4000 B) (c) Low power TTL (74L/54L) (d) Schottky TTL (Type 74S/54S) (e) Low power Schottky TTL (Type 74LS/54LS) (f) ECL (Type 10,000) Packages In Digital ICs Digital ICs come in different packaged forms: Dual-in-Line Package (DIP): Most TTL and MOS devices in SSI, MSI and LSI are packaged in 14-,16-,24- or 40- pin DIPs. Mini Dual-in-Line Package (Mini DIP): Mini DIPs are usually 8-pin packages.

Flat Pack: Flat packages are commonly used in applications where light weight is an essential requirement. Many military and space applications use flat packs. The number of pins on a flat pack varies from device to device. TO-5, TO-8 Metal Can: The number of pins on a TO-5 or TO-8 can vary from 2 to 12. TO-8 Metal Can TO-5 Metal Can Identification of Integrated Circuits Usually the digital integrated circuits come in a dual-in-line

(DIP) package. Sometimes, the device in a DIP package may be an analog componentan operational amplifier or tapped resistors and therefore, it is essential to understand as to how to identify a particular IC. In a schematic diagram, the ICs are represented in one of the following two methods: The IC is represented by a rectangle with pin numbers shown along with each pin. The identification number of the IC is given on the schematic. The IC is represented in terms of its simple logic elements. For example, IC 74 LS 08 is quad two-input AND Gate and when it is represented in a schematic, it is listed as 74 LS 08.

An IC can be identified from the information given on the IC itself. The numbering system, though standardized, has some variations from manufacturer to manufacturer. Usually, an IC has the following markings on its surface. Core Number: This identifies the logic family and its functions. In 74 LS 51, the first two numbers indicate that the IC is a member of the 7400 series IC family. The last letters give the function of the IC. Letters inserted in the centre of the core number show the logic sub-family. Since TTL is the most common series, no letter is inserted in the centre of the core number. In case of other families, the following letters are used: C = CMOS , L = Low Power ,LS = Low Power Schottky, S = Schottky , H = High Speed. The same numbered ICs in each family perform the same function and have the same pin numbers. They are however, not interchangeable because of differences in timing and power requirements.

The Prefix to the core number identifies the manufacturer. For example, SN shows a device from Texas instruments. Suffix to the core number indicates package type, temperature range, etc. In some ICs, marking is also provided for the year of manufacture and production batch. For example, 9834 indicates that the device was produced in 1998 in the 34th batch. The manufacturers logo (trade mark of the manufacturer) is also printed along with other information about the IC. IC Pin-Outs Packages for digital ICs generally fall into three categories, which are delineated below: Metal Case TO Type Packages: In these, all the pins are in a circle and are numbered in counter clock-wise direction when viewed from the bottom. The pin closest to the orientation tab has the

highest number. The most commonly used metal packages are TO-73 (12 leads), TO-99 (8 leads) and TO-101 (12 leads). Dual-In-line Packages (DIL or DIP): They have all leads arranged in two parallel lines. The most common package is T-116, which has 14 pins. Another most common package is a 16-pins DIP, which has the same overall dimensions as that of 14- pin- DIP. Flat Packages: They are smaller than the TO-16 packages and therefore allow higher packing density. They can be assembled on both sides of a PCB. They are preferred for use in military equipment Microprocessors A microprocessor, also known as a CPU or Central Processing Unit, is a complete computation device that is fabricated on a single chip. A chip is

basically an integrated circuit. Generally it is a small, thin piece of silicon onto which the transistors making up the microprocessor have been etched. A chip might be as large as an inch on a side and can contain as many as 10 million transistors. Simpler processors may contain only a few thousand transistors etched onto a chip. The first microprocessor to make it into a home computer was the Intel 8080, a complete eight-bit computer on one chip introduced in 1974. The first microprocessor to make a real revolution in the market was the Intel 8088, introduced in 1979 and incorporated into the IBM PC (International Business Machines Personal Computer), which appeared in the market around 1982. PC market moving from 8088 to the 80286, to the 80386, to the 80486, to the Pentium, to Pentium II, Pentium III and the now Pentium IV. All these microprocessors are made by Intel and are improvements on the basic design of the 8088. The new Pentiums can execute any piece of code that

ran on the original 8088, but the Pentium II runs about 3000 times faster than 8088. microprocessor does the following three basic things: Using its Arithmetic/Logic unit (ALU), a microprocessor can perform mathematical operations like addition, subtraction, multiplication and division. It can move data from one memory location to another. It can make decisions and jump to a new set of instructions based on these decisions. Most practical microprocessors use 40 or more pins,

and even keeping to that number requires that the eight data pins be used for both reading and writing. In the context of microprocessors, the following terms must be understood: Microns: This refers to the width, in microns, of the smallest wire on the chip. For comparison, a human hair is 100 microns thick. As the feature size on the chip goes down, the number of transistors rises. Modern microprocessors are based on 0.25 micron or less technology. Clock speed: This is the maximum rate that the chip can be clocked. The clock speed of modern microprocessors is over 2 GHz. Data Width: This is the width of the ALU. An 8-bit ALU can add/subtract/ multiply/etc. two 8-bit numbers, while a 32-bit ALU can manipulate 32bit numbers. An 8-bit ALU would have to execute four instructions to add two 32-bit numbers, while a 32-bit ALU can do it in one instruction.

In many cases, the external data bus is of the same width as the ALU, but not always. The 8088 had a 16-bit ALU and an 8-bit bus, while the modern Pentiums fetch data 64 bits at a time for their 32-bit ALUs. MIPS: This stands for Millions of Instructions Per Second, and is a measure of the performance of a CPU. The MIPS value of modern processors is around 1000, as compared to 1 MIPS for an 80286 processor. Microcontrollers A microcontroller is basically a single-chip microcomputer provided in a single integrated circuit package, which contains a CPU, clock circuitry, ROM (flash), RAM, serial port, timer/counter and I/O circuitry. Most of the microcontrollers come in 40-pin DIP packages; the pin-out consists essentially of upto 32 I/O lines with the remainder being used

for power, reset interrupt and timing. The instruction set of a single chip microcomputer generally bears a close resemblance to that of the microprocessor family to which the microcontroller belongs. Microcontrollers have been available for a long time. Intel introduced 8048 (MCS-48, an 8-bit microcontroller) in 1976. It has developed upwards and its new version is the 8051 family, which is a high performance 40-pin DIP package. Microcontrollers functionality has increased tremendously in recent years. Today, one gets microcontrollers which are stand-alone for applications in data acquisition systems and control. They have A/D converters on the chip which enable their direct use in instrumentation. Microcontroller is available in both DIP or QUAD package. Surface Mount Devices

The conventional through-hole mounting technology used for printed circuit assemblies is being increasingly superseded by surface mount technology. Instead of inserting leaded components through the holes, special miniaturized components are directly attached and soldered to the printed circuit board. The surface mounted components and their packing are particularly suitable for automatic assembly. The advantages of surface

mounting are rationalized production, reduced board size and increased reliability. The prime motivation for introducing surface mount technology (SMT) is, thus, density increase and board area reduction due to continuous demand and market trend for miniaturization in electronic assembly, particularly in portable products. In surface mount technology, the components can be assembled on both sides of the board. The components are attached to the PCB by solder paste or nonconductive glue and then soldered. Since not all component types are available in the surface mount version, a combination of leaded and surface mounted components is generally seen in manufactured electronic equipment. The 100 mil lead spacing used in DIL packages has a severe limitation in terms of the number of pins that could be accommodated in high density VLSI circuits, with 64 being the limit.

The small outline (SO) package SMD is available in which pins are on a 50 mil grid. For higher pin counts, the quad package with J leads has become a popular package in the industry. With the pin numbers going up to 300+, the pin spacing has been decreasing from 50 to 30 and then to 25 mil. Resistors, ceramic capacitors and discrete semiconductors represent 80 per cent of the total available SMDs. Normally, in the SMDs, the cubic shape prevails over cylindrical versions, as the latter can only have two pins thus being exclusively suitable for resistors, capacitors and diodes. If development of a special SMD package is not possible for electric or economic reasons, the DIP package can be converted into a surface mountable version by simply bending the leads. Lead Styles SMDs are constructed with different types of lead styles. Lead Pitch: The lead pitch in a SMD is measured from the centre tocentre of leads, and is not the air gap between the leads.

Component Packaging: Automated assembling of printed circuit boards is carried out by pick-and-place machines. For this purpose, proper packaging is required to protect the components, particularly the SMDs, from damage during transport or mount. Surface Mounting Semiconductor Packages With developments in the technology of surface mounting, a range of packaging types has emerged. The commonly used packages in semiconductor SMDs are: SOIC (Small Outline Integrated Circuit) This is a plastic package, available in 6, 8, 10, 14, and 16 versions with a body width of 4 mm, and in 16, 20, 24, and 28 pin versions with a wider body of

7.6 mm. SOT (Small Outline Transistor) Packages They are used for discrete transistors and diodes. The most common packages are the SOT-23 and the SOT-89 (now renamed as TO-236 and TO-243 respectively). SOD (Small Outline Diode) package is specifically designed for small diode chips, limited to a power dissipation of 250 mW. LCCC (Leadless Ceramic Chip Carriers) The term chip carriers

refers to those IC packages that are square or nearly square with their terminations brought out on all four sides. LCCC are those devices which do not carry any leads and excess packaging material. These packages are suitable for direct soldering or for attachment by sockets with added leads. LCCC are commonly available in 18, 20, 28, 32, 44, 52, 68, 84, 100, 124 and 156 termination versions. The component height is typically 1.52.0 mm. The pitch between the terminations is always 1.27 mm. PLCC (Plastic Leaded Chip Carriers) They are available in a wide range in the same sizes and formats as the LCCCs. The leads of these devices also have a pitch of 1.27 mm. The majority of

PLCCs are available with J leads that are folded underneath the package. Since the J leads are tucked under the device, and are not protruding, they present difficulties for the inspection and testing of circuits. Flat Packs and Quad Packs The flat pack package has its lead frame coplanar to the body of the package. The original flat pack had leads on two sides of the body, but presently they are available with leads on all four sides, and are accordingly called quad pack. LGA (Land Grid Arrays) In these devices, the pins emanate from an array on the under side of the package rather than its periphery. The surface mounting version of the leaded grid

array is the land grid array, whereby the pins are substituted by an array of solderable pads on the base. They are available in various sizes, pad sizes and pad densities to meet the requirements of different lead-out arrangements. BGA (Ball Grid Arrays) These refer to actually any type of IC package that routes from the die and connects to the PCB via solder bumps. The package provides solutions for high performance, high pin count applications, with pin counts now nearing 1000, with 300 to 600 being standard. Heat Sinks Electronic components, particularly semiconductor devices, show temperature-dependent characteristics. They can be permanently damaged by over-heating if the temperature of the device is not

maintained within specified limits. It is, therefore, necessary to determine how much heat an active component will generate and also to make arrangements for its dissipation. This is usually done by providing a heat sink. Discrete power devices are usually supplied in packages which can be easily assembled on to a heat sink. In such cases, it is necessary to ensure good contact between the package and its heat sinks, specially by interposing a thin layer of silicone grease to improve heat transfer where the metal surfaces may not be meeting, and by applying sufficient pressure through the screw connection. Power DIP packages are usually provided with a metal slug in the body to which good thermal contact can be made with an external heat sink. Some DIP packages have two side tabs to which the heat sink can be attached. It is sometimes possible to solder these tabs to a large copper

area on the component side of PCB and to use that as a heat sink. Transformer A transformer is an electrical device which, by electromagnetic induction, transforms electric energy from one circuit to another at the same frequency, but usually at a different voltage and current value. In electronic equipment, transformers are generally used to provide the required ac voltage to the circuit by appropriately transforming the mains voltage. When a transformer transfers electric energy at a different level, it is called either a step-up (increase in the voltage ratio) or a step-down (decrease in the voltage) transformer. If there is no level change, then it is said to have a 1:1 voltage ratio. A transformer is so constructed that one winding (primary) induces voltage into a second winding or windings (secondary). Transformer constructed with two or more windings wound on a common core.

The windings are adjacent to each other to obtain magnetic or inductive coupling. The input voltage is applied to the primary winding, and the output is taken from the secondary winding. The primary is normally shown on the left, so that the signal flows from left to right, with the output at the right. The transformer may have either an air or an iron core. The air core transformer is used for coupling signals between stages at higher frequencies. The power transformer is usually of iron core and has two or more secondary windings. Relays A relay is an electromechanical device. It depends upon the energizing of a magnetic coil (solenoid) in one circuit to control the opening or closing of contacts in a completely different circuit. The relay solenoid and the contacts of that relay may appear in different locations on the diagram.

The symbols for a relay resemble its actual construction and circuit operation. NC or NO. Solid State Relays With a sealed construction and no moving parts, the solid state relays are particularly suited to ac switching applications requiring long life and high reliability. The switching is silent, causes no arcing and is unaffected by vibration and corrosive atmospheres. The control input is optically isolated from the zero voltage switching circuit which produces virtually no RF interference. They are operated by a TTL open collector. The output circuit is normally open. These relays are available as SIL (single-in-line) or DIL (dual-in-line) PCB mounting type

packages. Connectors The connector on a printed circuit board provides a route for all input and output signals, voltages and grounds. The connectors on the board are usually of male contact type which can be plugged into a female receptacle. The symbol for a male contact looks like the head of an arrow, and for a

female contact, like the tail of an arrow. The type of contact can be shown graphically as either a plug or a jack. The plug must be shown at the top of the diagram with a dotted line joining each contact. The connector contacts are numbered on the diagram for convenience. They show the location of circuits, not necessarily in alphabetical or numerical order.

Recently Viewed Presentations

  • Vertebrate Zoology - Fall 2001

    Vertebrate Zoology - Fall 2001

    BI62- Vertebrate Zoology Origins and Classification of Early Fishes More primitive fishes - Palaeoniscids Bony Fish Phylogeny Class: Osteichthyes The bony fishes 30,000+ living species Internal skeleton of bone Remnants of placoderm armor remain as dermal scales in some species...
  • PEP -

    PEP -

    PEP Personal Information Name: Age: Height: Weight: School: Sports played: Specialist subject: GCSE PE Identified Sports Activity: Level played at: Identified Components of fitness: Strengths: Weaknesses: Introduction "The development of a personal exercise programme is central to the development of...
  • Asset 2013 - Asset and services management in Cape York ...

    Asset 2013 - Asset and services management in Cape York ...

    My work in Aurukun and other Cape York Indigenous communities was auspiced under the Local Government Asset Advanced program administered by the LGAQ and funded by the Federal government. [John] As you will see Aurukun is no different from remote...
  • Презентация PowerPoint - TehnoDent

    Презентация PowerPoint - TehnoDent

    Radiopacity of the material enables control for its position and homogeneity in the root canal. Optimal price-quality ratio. Advantages. Ensures homogeneity of the root canal filling without compression. Syringe with a reinforced plunger, convenient grip and Luer-Lock system ...
  • ELA-b Read180 4/3/18

    ELA-b Read180 4/3/18

    "Lose Now, Pay Later" by Carol Farley. Deb. Trinja. Trevor. In 2041, Deb and Trinja discover a new treat at the mall named Swoodies. They eat a lot and gain weight. They go to the mall again and see there's...
  • Wellbeing & Mental Health Network Tuesday 11th June

    Wellbeing & Mental Health Network Tuesday 11th June

    About London Youth. London Youth is a membership network of 450+ community youth organisations across London. We are a charity on a mission to improve the lives of young Londoners. We deliver a broad range of services to our members,...
  • School District Wellness Policies: Where do they Stand

    School District Wellness Policies: Where do they Stand

    Recess provides students with a needed break from their structured school day. It can improve children's physical, social, and emotional well-being,1,2 and enhance learning.3 Recess helps children meet the goal of 60 minutes of physical activity (PA) each day, as...
  • Offending behaviour programmes

    Offending behaviour programmes

    A reconviction outcome study of Core SOTP - Mews et al., (2017) 2562 Core programme men who completed the programme between 2000 - 2012 Compared to 13,219 men who did not do the Core programme