Transcription

SAFETY DATA SHEET:REGULAR MINERAL SPIRITSIN CASE OF TRANSPORTATION EMERGENCY CONTACT:CHEMTREC:(800) 424-9300----------------------ALL OTHER INQUIRIES:(770) 904-7042 // www.ciscochem.com266 Rue Cezzan Lavonia, GA 305531. IDENTIFICATIONCAS # 8052-41-3SYNONYMS:Naphtha, stoddard solvent, mineral spirits, white spiritGENERIC CHEMICAL NAME:Naphtha, high paraffinic, stoddard solvent, naphtha solventPRODUCT TYPE:Substance2. HAZARDS IDENTIFICATIONAPPEARANCE:COLORLESS LIQUIDODOR:PETROLEUM SOLVENTSIGNAL WORD:WARNING!FLAMMABLE LIQUID AND VAPORSTATIC ACCUMULATING LIQUID CAN BECOME ELECTROSTATIC ALLYIN BONDED AND GROUNDED EQUIPMENT; SPARKS MAY IGNITE LIQUIDAND VAPOR MAY CAUSE FLASH FIREHARMFUL IF SWALLOWED, CAN ENTER LUNGS AND CAUSE DAMAGEMAY CAUSE CHRONIC EFFECTSMAY CAUSE SKIN IRRITATIONMAY CAUSE EYE IRRITATIONMAY CAUSE RESPIRATORY TRACT IRRITATIONPROLONGED SKIN CONTACT MAY CAUSE IRRITATIONEXPOSURE ROUTES:INHALATION, INGESTION, SKIN AND/OR EYE CONTACTPHYSICAL:KEEP AWAY FROM HEAT, SPARKS AND FLAME. KEEP CONTAINERTIGHTLY CLOSED. USE ONLY WITH ADEQUATE VENTILATION.AVOID SPARK PROMOTERS. GROUND/BOND CONTAINER ANDEQUIPMENT. THESE ALONE MAY BE INSUFFICIENT TO REMOVESTATIC ELECTRICITYEYES:AVOID CONTACT WITH EYES. WASH THOROUGHLY AFTER HANDLINGSDS: REGULAR MINERALSPIRITSPage: 1

SKIN:AVOID CONTACT WITH SKIN AND CLOTHING. WASH THOROUGHLYAFTER HANDLINGSYMPTOMS OFOVER EXPOSURE:IRRITATION TO EYES, NOSE, THROAT; DIZZINESS; DERMATITIS;CHEMICAL PNEOMONITIS (aspiration liquid)MEDICAL CONDITIONSAGGRAVATED BYEXPOSURE:PRE-EXISTING DISORDERS INVOLVING ANY TARGET ORGANSMENTIONED IN THIS MSDS ARE BEING AT RISK MAY BE AGGRAVATEDBY OVER EXPOSURE TO THIS PRODUCT.CHRONIC EFFECTS:3. COMPOSITIONCAS #COMPONENTPERCENT8052-41-3STODDARD SOLVENT100HAZARDOUS CONSTITUENT(S) CONTAINED IN COMPLEX SUBSTANCESCAS #COMPONENTPERCENT100-41-4111-84-225551-13-7ETHYL BENZENENONANETRIMETHYL BENZENE(mixed isomers)0.11.0-8.00.5-5.0Component Regulatory InformationThis product may be regulated, have exposure limits or other information identified as the following: Stoddard solvent, EthylBenzene, Nonane, Trimethyl Benzene (See Section 8)4. FIRST AID MEASURESEYESCheck for and remove any contact lenses. Immediately flush eyes with plenty of water for at least 15 minutes, occasionally liftingthe upper and lower eyelids. Get medical attention immediately.SKINIn case of contact, immediately flush skin with plenty of water for at least 15 minutes while removing contaminated clothing andshoes. Wash clothing before reuse. Clean shoes thoroughly before reuse. Get medical attention immediately.INHALATION:Move exposed person to fresh air. If not breathing, if breathing is irregular or if respiratory arrest occurs, provide artificialrespiration or oxygen by trained personnel. Loosen tight clothing such as a collar, tie, belt or waistband. Get medical attentionimmediately.INGESTION:DO NOT INDUCE VOMITING. If conscious, rinse out mouth with water. Get medical attention immediately.NOTE TO PHYSICIANSNo specific treatment. Treat symptomatically. Contact poison treatment specialist immediately if large quantities have been ingestedor inhaled.SDS: REGULAR MINERALSPIRITSPage: 2

5. FIRE FIGHTING MEASURESFlammable PropertiesThis product is a flammable static accumulating liquid. Static accumulating liquid can become electrostatically charged even inbonded and grounded equipment. Sparks may ignite liquid and vapor may cause flash fire. Static electricity accumulation may besignificantly increased by the presence of small quantities of water or other contaminates. Restrict flow velocity to avoid build-up ofstatic charge. Refer to NFPA 77, API 2003, and CENELEC CLC/TR 50404 for further guidance.Extinguishing MediaUse dry chemical, CO2, water spray (FOG) or foamSpecific Hazards Arising from ChemicalElevated temperatures can lead to the formation of irritating fumes and vapors. Decomposition products may include the followingmaterials: Carbon dioxide and Carbon monoxide.Protective Equipment and Precautions for FirefightersFire-fighters should wear appropriate protective equipment and self-contained breathing apparatus (SCBA) with a full face-pieceoperated in positive pressure mode.6. ACCIDENTAL RELEASE MEASURESPersonal PrecautionsNo action shall be taken involving any personal risk or without suitable training. Evacuate surrounding areas. Keep unnecessary andunprotected personnel from entering. Do not touch or walk through spilled material. Shut off all ignition sources. No flares, smokingor flames in hazard area. Avoid breathing vapor or mist. Provide adequate ventilation. Wear appropriate respirator when ventilationis inadequate. Put on appropriate personal protective equipment.Environmental PrecautionsAvoid dispersal of spilled material and runoff and contact with soil, waterways, drains and sewers. Inform the relevant authorities ifthe product has caused environmental pollution.Methods for ContainmentStop leak if without risk.Methods for CleanupMove containers from spill area. Approach release from upwind. Absorb with an inert dry material and place in an appropriate wastedisposal container. Dispose of via a licensed waste disposal contractor.7. HANDLING AND STORAGEHandling ProceduresEating, drinking, and smoking should be prohibited in areas where this material is handled, stored and processed. Workers shouldwash hands and face before eating, drinking and smoking. Remove contaminated clothing and protective equipment before enteringeating areas. Do not get in eyes or on skin or clothing. Do not ingest. Avoid breathing vapor or mist. Use only with adequateventilation. Use non-sparking tools.Shipping and Storing ProceduresStore in accordance with local regulations. Store in a segregated and approved area. Keep in the original container protected fromdirect sunlight in a dry, cool and well-ventilated area, away from incompatible materials. Do not store in unlabeled containers. Storeand use away from heat, sparks, open flame or any other ignition source. Take precautionary measures against electrostaticdischarges. To avoid fire or explosion, dissipate static electricity during transfer by grounding and bonding containers and equipmentbefore transferring material. Empty containers that retain product residue may be hazardous. Do not reuse container.8. EXPOSURE CONTROLS AND PERSONAL PROECTIONComponent Exposure LimitsStoddard SolventACGIH TLV:TWA:100ppmOSHA PEL:TWA:500 ppmSDS: REGULAR MINERALSPIRITSTWA:Page: 32900 mg/m3

NIOSH REL:TWA:N/A ppmTWA:350 mg/m3NIOSH Ceiling:1800 mg/m3 [15 minute]Ethyl BenzeneACGIH TLV:TWA:20 ppmTWA:N/A mg/m3OSHA PEL:TWA:100 ppmTWA:435 mg/m3NonaneACGIH TLV:TWA:200 ppmTrimethyl Benzene (all isomers)ACGIH TLV:TWA:25 ppmN/A signifies not available.ENGINEERING CONTROLSThis product is a static accumulating liquid. Ground/bond container and equipment. These alone may be insufficient to remove staticelectricity. Material should be handled in enclosed vessels and equipment. Use only in adequate ventilation. Use process enclosures,local exhaust ventilation or other engineering controls to keep worker exposure to airborne contaminants below any recommended orstatutory limits.EYE/FACE PROTECTIONChemical goggles or face shieldSKIN PROTECTIONChemical resistant, impervious gloves complying with an approved standard should be worn at all times. Coveralls, apron, and bootsas necessary to minimize contact.RESPIRATORY PROTECTIONUse a properly fitted, air-purifying or air-fed respirator complying with an approved standard if a risk assessment indicated this isnecessary. Respirator selection must be based on known or anticipated exposure levels.GENERAL HYGIENEWash hands, forearms and face thoroughly after handling chemical products, before eating, smoking and using the lavatory and atthe end of the working period. Appropriate techniques should be used to remove potentially contaminated clothing.9. PHYSICAL AND CHEMICAL PROPERTIESNote: Physical and chemical properties are provided for safety, health and environmental considerations only and may not fullyrepresent product specifications. Please see the Product Specification Sheet for further information.Appearance:ColorlessOdor:Petroleum solventPhysical State:LiquidFlash Point (f):105Boiling Point (f): 310Vapor Pressure(mm Hg at 20 C):0.62Water Soluble:NOSDS: REGULAR MINERALSPIRITSPage: 4

Specific Gravity (g/cc):.77Density (lbs/gal)6.4PH:Not available10. STABILITY AND REACTIVITYStability:Stable under normal conditions. If heated, product’s static accumulation willrise and could cause flash fire.Polymerization:No polymerizationIncompatibility:Strong acids and oxidizing materialsConditions to Avoid:High temperatures, sparks, flamesHazardous DecompositionProducts:Does not decompose at ambient temperatures11. TOXICOLOGICAL INFORMATIONAcute ExposureMinimally toxic. Negligible hazards at ambient/normal handling temperatures.Respiratory IrritationIf material is misted or if vapors are generated from heating, exposure may cause irritation of mucous membranes and the upperrespiratory tract. Based on data from components or similar materials.Eye IrritationMay cause eye irritation. Vapors formed from heating may cause eye irritation.Skin IrritationMay cause skin irritationSensitizationNot expected to cause skin or respiratory sensitization.Component Analysis – LD50 / LC50Acute Toxicity Estimate (ATE) Values for Product:Inhalation LC50 Rat21 mg/L 1 HROral LD50 Rat 7000 mg/kgDermal LD50 Rabbit 2000 mg/kgChronic ExposureTarget Organ EffectsVapor/aerosol concentrations above recommended exposure levels are irritating to the eyes and respiratory tract, may causeheadaches, dizziness, anesthesia, drowsiness, unconsciousness and other central nervous system effects including death.Prolonged or repeated direct exposure to the skin results in symptoms of irritation and redness, dermatitis or oil acne.SDS: REGULAR MINERALSPIRITSPage: 5

Small amounts of liquid aspirated into the lungs during ingestion or from vomiting may cause chemical pneumonitis or pulmonaryedema.CarcinogenicityContains Ethyl Benzene which is considered a carcinogen under IARC. It has caused cancer in laboratory animal studies. Therelevance of these findings to humans is uncertain.MutagenicityNo data available to indicate product or any components present at greater than .1% are mutagenic or genotoxic.Reproductive ToxicityNo data available to indicate either product or components present at greater than .1% that may cause reproductive toxicity.TeratogenicityNo data available to indicate product or any components contained at greater than .1% may cause birth defects.12. ECOLOGICAL INFORMATIONComponent Analysis- Ecotoxicity – Aquatic LifeDuration/T est/Species96 Hr LC50Pimephals promelasConcentrations/ConditionsN/A mg/LDegradabilityNot determinedBioaccumulationNot determinedSoil MobilityNot determined13. DISPOSAL CONSIDERATIONSDisposal InstructionsThe generation of waste should be avoided or minimized wherever possible. Treatment, storage, transportation and disposal must bein accordance with applicable Federal, State/Provincial, and Local regulations.14. TRANSPORT INFORMATIONEMERGENCY RESPONSE GUIDE NUMBER: 128U.S. DOT BULK (OVER 119 GALLONS)UN 1268, PETROLEUM DISTILLATES , N.O.S. (Naphtha solvent), 3, PG III, combustible liquidBulk container must be labeled on two opposing sidesU.S. DOT Non-bulk (under 119 gallons)Not regulated.Exempt from labeling and placarding unless shipped via Air or Vessel*Truck/Rail car must be placarded on all 4 sides if aggregate gross weight exceeds 1,000 pounds15. REGULATORY INFORMATIONSARA Extremely HazardousSDS: REGULAR MINERALSPIRITSPage: 6

Substances (Sections 302 & 304)This product does not contain greater than 1% of any “extremely hazardous substances” listed pursuant to Title III of the SuperfundAmendments and Reauthorization Act of 1986 (SARA) Section 302 or Section 304 as identified in 40 CFR Part 355, Appendix Aand B.SARA Section 313This product contains the following components in concentrations greater than 0.1% for carcinogenic substances and/or 1.0% of thesubstances subject to the reporting requirements of Section 313 of Title III of the Superfund Amendments and Reauthorization Actof 1986 and 40 CFR Part 372:Ethyl Benzene (CASRN: 100-41-4): 0.1%1,2,4 Trimethylbenzene (CASRN: 95-63-6): 2.7%SARA Section 311 & 312 ClassificationsAcute Hazard:NOChronic Hazard:YESFire Hazard:YESReactivity Hazard:NOCERCLAThis product contains the following components listed under the Comprehensive Environmental Response, Compensation andLiability Act of 1980 (CERCLA) in 40 CFR Part 302, Table 302.4:Ethyl Benzene (CASRN: 100-41-4): 0.1% RQ 1,000 lbs.CALIFORNIA PROP 65This product contains chemical(s) known to the state of California to cause cancer and/or birth defects.Clean Water Act / Oil Pollution ActThis product may be subject to regulation by Section 311 of the Clean Water Act and the Oil Pollution Act. Releases of the productinto or leading to surface waters must be reported to the National Response Center at 1-800-424- 8802.PA RIGHT TO KNOW ACTThis product contains the following components listed under the Pennsylvania Right To Know Act:Stoddard Solvent (CASRN: 8052-41-3)N-Decane (CASRN: 124-18-5)N-Nonane (CASRN: 111-84-2)1,2,4 Trimethylbenzene (CASRN: 95-63-6)Ethyl Benzene (CASRN: 100-41-4)Global Chemical InventoriesINVENTORYUS TSCAEUJAPANAUSTRALIANEW NCOMPONENTALL COMPONENTSPresent*PresentNot availablePresentPresentPresentNot AvailablePresentPresentPresentPresent*May be subject to TSCA 12b export notification. Contains Nonane (CASRN: 111-84-2) at 7.85%.SDS: REGULAR MINERALSPIRITSPage: 7

16. OTHER INFORMATIONUS NFPA RatingsHEALTH1HIMIS RATINGSHEALTH1*FIRE2INSTABILITY0FIRE2PHYSICAL HAZARDS0Precautionary LabelsSignal WordWARNING!Flammable liquid and vaporStatic accumulating liquid can become electrostatically charged even in bonded and grounded equipment; Sparks may ignite liquidand vapor may cause flash fireHa